Hobart 120V/240V Airforce 27i Plasma Cutter with MVP
Item # 380651099
Buy a Welder and Get 15% off Welder accessories.
Get everything you need
Neighbor’s Club Members earn points with purchases.
Item # 380651099
Buy a Welder and Get 15% off Welder accessories.
Valid 5/11/2026 - 7/5/2026Apply now
Shopping at
Grassland (franklin) TN
Delivery to
37027
Pickup Nearby at FAIRVIEW TN(13.2) miles Free
Ship to store at Franklin TN
Free standard delivery on online footwear & Clothing purchases of $49 and over.
Get everything you need
Neighbor’s Club Members earn points with purchases.
Hobart Airforce 27i Plasma Cutter with MVP can be used on 120 V or 240 V input power. This plasma cutter clean cuts 3/8 in. steel. Our plasma cutter's dual-voltage capability with MVP allows you to connect to common 120 or 240 V power receptacles without the use of any tools - simply choose the plug that fits the receptacle. Its wind tunnel technology saves you from replacing parts by preventing abrasive dust and particles from damaging internal components. The Hobart Airforce plasma cutter automatically controls the amount of usage and flow of air or gas so you don't have to.
For additional information on this product, please see the Product Documents section for all downloadable user manuals, installation guides, brochures and warranty statements.
- Dual-voltage capability with MVP (Multi-Voltage Plug) - allows you to connect to common 120 or 240 V power receptacles without the use of any tools - simply choose the plug that fits the receptacle
- XT30R torch - Increases your comfort with an ergonomic safety trigger
- Wind tunnel technology - Plasma cutter saves you from replacing parts by preventing abrasive dust and particles from damaging internal components
- Fan-on-demand - The fan only runs when needed, reducing the dust and debris that is pulled into your machine
- Power factor correction (PFC) circuitry - PFC expands your work area via extension cord, while minimizing nuisance circuit breaker trips caused by voltage drops
- LVC line voltage compensation - Provides you steady and cleaner-ending cuts by using peak performance power under variable input voltage conditions (15%)
- Internal gas/air filter and regulator - Automatically controls the amount of usage and flow of air or gas so you don't have to
- Starts without high frequency - Protects your unit by not interfering with or damaging controls or computers
- Hobart Airforce plasma cutter draws up to 30% less amperage for the same cutting range as compared to the competition
| Brand | Hobart |
|---|---|
| Country of Origin | Made in USA |
| Airflow Volume | 3 CFM |
| Compatible Metal | Steel |
| Duty Cycle | 200 IPM |
| Features | The AirForce 27i with MVP (multi-voltage plug) technology can be used on 120 V or 240 V input power. Clean cuts 3/8" steel. |
| Ground Clamp Length | 12 ft. |
| Maximum Amperage Output | 30 A |
| Maximum Cutting Thickness | 5/8 in. |
| Maximum Input Amperage | 15 A |
| Maximum Input Frequency | 120 v |
| Maximum Input Voltage | 110/115/120V, 220/230/240 V |
| Maximum Open Circuit Voltage | 400V |
| Minimum Amperage Output | 20A |
| Minimum Generator Power Required | 110V |
| Power Cord Length | 10 ft. |
| Product Height | 11.25 in. |
| Product Length | 8.25 in. |
| Product Weight | 27.6 lb. |
| Product Width | 14.25 in. |
| Torch Length | 12 ft. |
| Warranty | 5/3/1 |
| Phase | Single Phase |
| Work Cable Length | 12 ft. |
| Manufacturer Part Number | 500575 |
Q: Does this have built in air compressor
2 years ago- A: Hi Bob99, Yes, you will want a compressor that is capable of putting out at least 5 CFM @ 90psi.2 years agoHelpful?
Q: Does this have a built in air compressor?
4 years ago- A: No, you will want a compressor that is capable of putting out at least 5 CFM @ 90psi.4 years agoHelpful?
Q: What size breaker is needed for 220 volt use.
4 years ago- A: It will operate on a 20 amp but if you want the full 27 amp output you will need to install a 30 amp 120 volt service.4 years agoHelpful?
Q: Is this a pilot arc machine?
4 years ago- A: All Hobart Plasma cutters (in current production) use pilot arc start verses a high frequency arc start.4 years agoHelpful?
Q: does this have a built-in compressor
5 years ago- A: No, it does not.5 years agoHelpful?
Q: The picture is the same as the 12i and do you sell the new model of the airforce 27i northern tool has the new model for 1299
Anonymous5 years ago- A: They didn’t have at my location but I was able to buy on the website.5 years agoHelpful?
Q: Can it be run off the hobart elite welder?
5 years ago- A: Hobart 500565 Airforce 27i Plasma Cutter with MVP can be used on 120 V or 240 V input power.5 years agoHelpful?
Q: What country is this product made in?
5 years ago- A: Tag on mine is Appleton WI, USA5 years agoHelpful?
Q: Does it use argon gas?
5 years ago- A: No just compressed air.5 years agoHelpful?
Q: Is this what it being sold. Because what is pictured on hobarts website under airforce 27 I is not what is pictured
5 years ago- A: airforce 27 I is 120v or 240v i use 240 in my shop5 years agoHelpful?
Similar Items
-
-
-
Top Rated
-
Top Rated
-
-
-
Top Rated
-
-
-
Top Rated
-
-
Items You May Like
-
-
-
Top Rated
-
Top Rated
-
-
-
-
-
-
Top Rated
-
-
Customers Also Bought
-
-
Top Rated
-
-
-
-
-
-
Top Rated
-
Top Rated
-
-
-
Reviews
- purchase
- cutting
- satisfaction
- price
- metal
- weight
- ease of use
- quality
Good Stuff
Yes, I recommend this product.
Great purchase. Works great.
Yes, I recommend this product.
Hobart Quality
Yes, I recommend this product.
Hobart
Yes, I recommend this product.