Skip to Main Content

For security, click here to clear your browsing session to remove customer data and shopping cart contents, and to start a new shopping session. 

Tractor Supply Co.

We Are Listening...

Say something like...

"Show me 4health dog food..."

You will be taken automatically
to your search results.

Please enable your microphone.

Your speech was not recognized

Click the microphone in the search bar to try again, or start typing your search term.

We are searching now

Your search results
will display momentarily...

Main Content

Culvert HDPE 24 in. x 20 ft. Corrugated Pipe, HDPE 2420

SKU: 133085799
Culvert HDPE 24 in. x 20 ft. Corrugated Pipe, HDPE 2420
Enter Zip Code for price More Info
Product price

Save Up To
See price at checkout More Info
No ratings found


TSC of bennington #753
300 depot st
bennington, VT 05201
(802) 440-9937
TSC of bennington #753
300 depot st
bennington, VT 05201
(802) 440-9937
Check Availability at Other Stores
Standard Delivery Not Available to 
Notice: This item will ship within 4 days.
This product may require up to 4 additional days for order processing prior to shipping.
Change Delivery Location
Note: This product cannot be shipped to AZ,CA,CO,ID,MT,NV,NM,OR,UT,WA,WY

Item Information

Culvert HDPE 24 in. x 20 ft. Corrugated Pipe

  • Manufactured with smooth interior allowing for more efficient flow
  • Designed with a bell and spigot with a gasket for a water tight joint
  • Excellent abrasion and corrosion resistance
  • Long term drainage solution
  • High Density Polyethylene
  • Our culverts are DOT approved. They will support the weight of any DOT approved vehicle when installed correctly. If unsure of how to properly install, please seek professional advice.
Meets or exceeds AASHTO M252 and AASHTO M294 Type S

Specification Description
Application/Use: Used in driveway and roadway culverts
Type: HDPE Culvert
Product Weight: 231 lb.
Product Length: 20 ft.
CountryofOrigin: Made in USA
Operating Temperature Range: N/A
Part Number: HDPE 2420
Material: High Density Polyethylene
Special Feature(s): N/A
Maximum Operating Pressure: N/A
Product Inner Diameter: 24 in.
Product Width: 26.75 in.
Product Outer Diameter: 26.75 in.
Number of Walls: 1
Wall Thickness: 2.75 in.
Manufacturer Part Number HDPE 2420

Is there a way to cap both ends to make a water tight pontoon?

Asked by: AbelmannT
These products are designed specifically for drainage. We do not recommend using as a pontoon.
Answered by: CodyP
Date published: 2019-06-18

Can these be cut into 10' sections?

Asked by: RandalWildcat
Yes, a reciprocating saw can be used.
Answered by: MatthewL
Date published: 2019-05-21

Does the bell and spigot allow you to literally screw these lengths together to join them for added length?

Asked by: COL T
The HDPE pipe actually slide together. The spigot is equipped with a rubber gasket.
Answered by: Alicia M
Date published: 2019-01-23

Is there any way to install a valve inside of pipe to control water flow?

Asked by: Beaver Man
There is no recommended way to install a valve inside of the HDPE pipe. However, gate valves can be installed on a concrete headwall at the end of the HDPE pipe. This is a very in depth process, professional installation is highly recommended.
Answered by: AshleyBe
Date published: 2018-11-06

Can you drive over these? What’s the weight load that these can take?

Asked by: Wanttoknow33
These culverts are DOT approved, so they will technically support the weight of any DOT approved vehicle when installed correctly. We recommend seeking professional advice when installing if you are unsure om how to properly install.
Answered by: JasmineH
Date published: 2018-11-05

How flexible is the 2420? If I have to go around a bend, will it flex enough or is it rigid?

Asked by: chestercopperpot

can these be used as a protective casing for an underground bore

Asked by: const123
The vendor says the item should act as a protective casing as long as the pipe is installed correctly.
Answered by: richardm
Date published: 2019-08-19

Is there a prescribed manner to join two lengths at a 45° or 90° angle, or is there such a manufactured joint? If not, what is the flex (in inches over a 20' length)?

Asked by: Homestead001
We would suggest seeking professional installation advice for this type of question.
Answered by: NRoberts
Date published: 2019-04-12
  • y_2020, m_2, d_25, h_12CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.5
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_11
  • loc_en_US, sid_133085799, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING)]
  • clientName_tractorsupply
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • LOCAL, getContent, 5ms